• Description
• Specification
• Reviews

• Description
• Specification
• Reviews

Alpha A65 w/800TVL  150° camera BNF Specs:

• SucceX F4 1S 5A AIO Whoop Board  w/VTX
• XING 0802 22000KV FPV Micro Motor
  
• Wheelbase: 65mm
• Body size: 46*46mm
• Ducted propeller size: 31mm
• FC pattern: 25.5*25.5mm
• Weight: 24.5g (without battery)
• Flight time: 3-4 min cruising (1S 300mAh)

FC // SucceX F4 1S 5A AIO Whoop Board

Size：29*29mm

Mounting pattern: 25.5*25.5mm/φ3mm （half-hole)

Connector：Micro-USB

Weight: 5.4g (with power cable, vtx, and vtx antenna)

MCU：STM32F411

Gyro：MPU6000

Blackbox：no

BEC output：5V 1.2A

INA pad：n uart2

Barometer：no

FC Firmware：MatekF411RX

ESC Firmware：O-H-05 BLS

ESC // 5A 

Current: 5A continuous and peak 6A

Current scale: 400

Input：1S

Signal Support: Dshot，Oneshot，Multishot

Current sensor：yes

BLHeli：BLHeli-S

ESC Telemetry：no

FPV cam: 

Power DC: 5V

Size: 14*12.2*12mm

Net weight: 1.6g

800TVL 150°

VTX：

Input voltage: 5V

Channels: 48CH

Power: PIT/25/50mW

Connector:UFL/IPEX

iF8 FPV Remote Controller

Size: 160*130*45mm

Weight: 233g

Frequency: 2.400GHZ-2.480GHZ

RF Module: Multi-Protocol Module Compatible (CC2500）

Protocol Options: D8 / D16 v1 FCC / D16 v1 LBT / D16 v2 FCC / D16 v2 LBT (No Frsky ACCESS support)

Max. Tansmission Power: 20dB

Antenna gain: 2dBi

Range: 1~2km @ 20dB (depending on noise floor and RX)

Battery: Built in 3.7V 1000mAh Lithium battery

Charging: Built in USB-C charging

Firmware: OpenTX iF8 Edition (Special iF8 Edition)

Multiprotocol-TX-Module（Stick input protocol selection）

Channels: Up to 8 channels (depending on the model / receiver)

Compatibility

– All D8 and D16 compatible receivers!

– Frsky ACCST protocol (no ACCESS protocol supported)

– iF8 D8RX Receiver (LINK)

– iF16 Receiver

iFlight FPV Goggles with DVR Function

Frequency: 40CH 5.8GHz

Built-in battery: 3.7V/2000mAh Battery

Size: 155*144*113mm

Weight: 295g with 3.7V 2000mAh battery

Headband: 3-Sided Adjustable Headband

Screen size: 4.3 Inch

Resolution: 800*480 (no blur after enlarge by the lens)

Brightness: 300cd/m2 with special high brightness backlight LED for outdoor FPV

TF card: support up to 32G

Main Feature:

With DVR function video recording, picture saving

High brightness 4.3 inch LCD specially turned for FPV racing or Model airplane.

Built-in super sensitiveness 5.8GHz 40ch receiver, especially with RaceBand includes race frequency.

Come with advanced auto-searching function ad show you the working frequency on screen.

Built-in 3.7V/2000mAh battery, each full charge revive around 3.5 hours working time. 3.5 hours working time.

Ergonomic design fit your faces.

92% transparent lens adopted, no distort, no blur on the adage of screen;

Light weight 295g with 3hr 2000mAh battery, RTF for any scale, racing, Model airplane game.

4.3 inch 480*272px HD high brightness LCD.

R81 Receiver

• Frequency: 2400-2483.5Mhz
• Dimension: 17*11mm
• Weight: 2g
• Numbers of Channel: 8
• Signal form: D8
• Output Formal: SBUS inverted / output RSSI
• Operating Voltage: 4.5-6V
• Antanna Length: 9cm

Fullsend 1S HV 300mAh 40C Lipo Batteray-PH2.0 (5pcs)

-Minimum Capacity: 300mAh

-Configuration: JST-PH2.0 /HV4.35V/3.8V/1.14WH

-Discharge Rate: 40C

-Max Burst Discharge Rate: 60C

-Net Weight: 8.1g

-Dimensions: 65*11*6mm

-Charge Plug: JST-PH2.0

Caution:

*Don’t over-charge or over-discharge batteries.

*Don’t put it beside the high-temperature condition.

*Don’t throw it into the fire.

*Don’t throw it into the water.

1S JST PH2.0 Type-C Battery Charger:

ONLY support LiHV 3.8V/4.35V 1S battery, not for 4.20V 1S LiPo battery

Support 0.2A/0.6A charge current by switch button

TYPE-C power supply interface input range: 5V plusmn; 5% on 0.5~2A, suggested 2.4A

Charger plug: JST-PH 2.0

The LED light indicate the charging state, LED on red solid indicates charging, LED on green indicates full charged.

Battery charging termination voltage:LiPo type 4.35V plusmn; 0.5%

Product weight: 1.6g

• Description
• Specification
• Reviews